The following config is for a Patton 4960 Gateway.
The gateway is configured with a single PRI.
#----------------------------------------------------------------#
- #
- SN4960/4E24V/UI #
- R4.T 2006-12-11_RFE438 H323 RBS SIP #
- 2007-02-02T01:22:53 #
- Generated configuration file #
- #
#----------------------------------------------------------------#
cli version 3.20
administrator administrator password xxxxxx encrypted
clock local offset -08:00
- Put in your DNS Server
dns-client server xxx.xxx.xxx.xxx
dns-relay
webserver port 80 language en
sntp-client - Put in your primary and secondary SNTP time server
sntp-client server primary xxx.xxx.xxx.xxx port 123 version 4
sntp-client server secondary xxx.xxx.xxx.xxx port 123 version 4
sntp-client poll-interval 36000
sntp-client local-clock-offset - Enter your gateway's fqdn
system hostname gateway.xyz.com
system
ic voice 0
pcm law-select uLaw
system
clock-source 1 e1t1 0 0
clock-source 2 internal
profile napt NAPT_WAN
profile napt NAPT
profile ppp default
profile call-progress-tone US_Dialtone
profile call-progress-tone US_Alertingtone
play 1 2000 440 -19 480 -19
pause 2 4000
profile call-progress-tone US_Busytone
play 1 500 480 -24 620 -24
pause 2 500
profile tone-set default
profile tone-set US
map call-progress-tone dial-tone US_Dialtone
map call-progress-tone ringback-tone US_Alertingtone
map call-progress-tone busy-tone US_Busytone
map call-progress-tone release-tone US_Busytone
map call-progress-tone congestion-tone US_Busytone
profile voip default
codec 1 g711ulaw64k rx-length 20 tx-length 20
codec 2 g711alaw64k rx-length 20 tx-length 20
profile pstn default
profile sip default
profile aaa default
method 1 local
method 2 none
context ip router
interface WAN
ipaddress dhcp
use profile napt NAPT_WAN
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
interface LAN
- Enter the IP address of your gateway
ipaddress xxx.xxx.xxx.xxx 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
context ip router
- Enter your default gateway
route 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 0
context cs switch
digit-collection timeout 4
routing-table called-e164 TAB_OUT
route .%T dest-interface IF-SIP1
routing-table called-e164 TAB_IN
route default dest-service OUTBOUND
mapping-table called-e164 to called-e164 STIP-ALL
map default to ""
interface isdn IF_PRI_1
route call dest-table TAB_OUT
use profile tone-set US
caller-name send-information-following
user-side-ringback-tone
interface sip IF-SIP1
bind gateway GW-SIP
service default
route call dest-table TAB_IN
- Enter your SIP domain name
remote xyz.com
no address-translation incoming-call calling-uri
service hunt-group OUTBOUND
drop-cause normal-unspecified
drop-cause no-circuit-channel-available
drop-cause network-out-of-order
drop-cause temporary-failure
drop-cause switching-equipment-congestion
drop-cause access-info-discarded
drop-cause circuit-channel-not-available
drop-cause resources-unavailable
route call 1 dest-interface IF_PRI_1
context cs switch
no shutdown
gateway sip GW-SIP
bind interface LAN router
service default
- Enter your SIP domain name below
registration manual xyz.com
gateway sip GW-SIP
no shutdown
port ethernet 0 0
medium auto
encapsulation ip
bind interface WAN router
no shutdown
port ethernet 0 1
medium auto
encapsulation ip
bind interface LAN router
no shutdown
port e1t1 0 0
port-type t1
clock slave
linecode b8zs
framing esf
encapsulation q921
q921
permanent-layer2
uni-side user
encapsulation q931
q931
- set your protocol to ni2 might also be dms100
protocol ni2
uni-side user
bchan-number-order ascending-cyclic
encapsulation cc-isdn
bind interface IF_PRI_1 switch
port e1t1 0 0
no shutdown
port e1t1 0 1
port-type e1
clock master
framing crc4
shutdown
port e1t1 0 2
port-type e1
clock master
framing crc4
shutdown
port e1t1 0 3
port-type e1
clock master
framing crc4
shutdown